SciELO - Scientific Electronic Library Online

 
vol.11 número3Análisis termoenergético del sistema de generación de vapor de una central térmica de 49 MWAnálisis comparativo de la eficiencia estabilizadora de asfaltenos del aceite de cáscara de Anacardium occidentale y productos comerciales índice de autoresíndice de materiabúsqueda de artículos
Home Pagelista alfabética de revistas  

Servicios Personalizados

Revista

Articulo

Indicadores

Links relacionados

  • No hay articulos similaresSimilares en SciELO

Compartir


Enfoque UTE

versión On-line ISSN 1390-6542versión impresa ISSN 1390-9363

Enfoque UTE vol.11 no.3 Quito jul./sep. 2020

https://doi.org/10.29019/enfoque.v11n3.631 

Misceláneos (Miscellaneous)

Manufacture material characteristic analysis of original and alternative auto parts. Case Study: Brake Disc

Análisis de las características del material de fabricación de autopartes originales y alternos. Caso de estudio: Disco de freno

Jaime Antamba1 

Vladimir Azanza2 

Gorky Reyes3 

Álvaro Remache4 

Soraya Ruiz5 

1Universidad Internacional del Ecuador, Quito - Ecuador (jaantambagu@uide.edu.ec)

2Universidad Internacional del Ecuador, Quito - Ecuador (edazanzalu@uide.edu.ec)

3Universidad Internacional del Ecuador, Quito - Ecuador (gureyesca@uide.edu.ec)

4Universidad Internacional del Ecuador, Quito - Ecuador (alremachech@uide.edu.ec)

5Universidad Internacional del Ecuador, Quito - Ecuador (soruizru@uide.edu.ec)


Abstract

All powered vehicles have a braking system adopted according to the type of vehicle and work for which they are designed. In Ecuador, there is a great variety of auto parts that are proposed as alternative replacement, varying in cost and quality. This research aims to quantitatively analyze the characteristics of the brake disc material between original and alternate auto parts. This research analyzes three brake disc samples (A, B, C) from different manufacturing sources, using the ASTM E415-08 spectrometry test and the metallography test under the ASTM A247-16A standard. The spectrometry detects 15 elements in each sample, the carbon equivalent of sample A is 18% and 20% higher in relation to sample B and C, which significantly influences the microstructure. The metallographic tests indicate a pearlitic matrix in each sample, however, there is a different distribution and size of the graphite flakes. According to the SAE J431 standard, each auto part meets the material conditions for the brake disc function.

Keywords SAE J431; perlitic matrix; carbon equivalent; auto parts

Resumen

Todos los vehículos propulsados cuentan con un sistema de frenado adoptado según el tipo de vehículo y trabajo para el que están diseñados. En Ecuador existe una gran variedad de autopartes que se proponen como repuesto alternativo, que varían en costo y calidad. Este estudio tiene por objetivo analizar cuantitativamente las características del material de discos de freno entre autopartes originales y alternas. El estudio analiza tres muestras de disco de frenos (A, B, C), de diferente procedencia de fabricación, utilizando la prueba de espectrometría ASTM E415-08 y la prueba de metalografía, bajo la normativa ASTM A247-16A. La espectrometría detecta 15 elementos en cada muestra. El carbono equivalente de la muestra A es superior en un 18 % y 20 % en relación a la muestra B y C, lo cual influye significativamente en la microestructura. Los ensayos metalográficos, indican en cada muestra una matriz perlítica; sin embargo, existe una diferente distribución y tamaño de las hojuelas de grafito. Según la norma SAE J431, cada autoparte cumple con las condiciones de material para la función de disco de freno.

Palabras clave SAE J431; matriz perlítica; carbono equivalente; autoparte

1. Introduction

Currently in the Ecuadorian market, a variety of auto parts are offered, both in brand and origin, at the same time, they go hand in hand with the quality and cost of the spare part. The cost factor can be influential when making a decision, because customers decide to buy, considering the cheapest option, without considering the best option in safety or performance.

In the vehicle, two safety systems coexist: passive and active; the former are those that work at specific moments when their action is activated, for example, airbags and the anti-lock braking system (ABS) (Bosch, 2005). Meanwhile, active systems, such as the braking system, are always in operation, the main means of ensuring the safety of the occupants of the moving vehicle. The frictional heat generated on the surface of the brake disc can influence an excessive increase in temperature which, in turn, causes undesirable effects such as thermal elastic instability, premature wear, brake fluid vaporization and thermally excited vibrations (Belhocine, A. & Bouchetara, M., 2012). It is important to analyze the composition of the material, as well as the microstructure of the different brake discs in the national market to verify their performance capacity according to the design conditions.

The Metallurgical Engineering Department of the University of Santiago de Chile has carried out studies of premature wear and abnormal mechanical vibrations in brake discs based on their chemical composition, concluding that such failure is produced by residual stresses originated by the difference that exists in the material composition of the different areas of the disc. These stresses were relaxed during the friction process to which the disc was subjected during its service and were the cause of the deformation of its geometry. (Piña, 2008) (Tuckart, Molinari, Caso, & Prieto, 2014). This study indicates that in the process of casting the piece, there may be failures produced by differences in the composition of the material, that is, there is a possibility that pieces with these possible failures are marketed at a regional level (Rodrigues, 2004).

The materials of the brake discs are generally made of grey cast iron. The regulation that governs the different grades of grey iron for the automotive industry is the SAE J431 standard, which determines certain grades for the manufacture of brake discs and drums (Rodríguez, 2004). Within the methods to analyze the composition of a metallic alloy, by the type of material and part, a spark type spectrometry is considered (Piña, 2008).

This research, proposes a comparative analysis of brake disc material between original and alternate auto parts. Due to the large share of alternative parts offered by the market at considerably lower costs compared to the originals, a comparison of the different compositions and microstructures that could present these options was made and it was analyzed whether these factors could affect their operation.

2. Methodology

The research process is descriptive and experimental. This research analyzes three brake disc samples (A, B, C) from different manufacturing sources, using the ASTM E415-08 spectrometry test to establish the components of each sample and the metallography test under the ASTM A247-16A standard to establish the type of matrix and the graphical distribution.

2.1 Vehicle

In the case of Ecuador, the age of the vehicle fleet is led by 28.99 % of cars between 1-5 years and followed by 21.44 % of cars between 5-10 years (AEADE; 2018). The third brand in the market is Hyundai, surpassed by Chevrolet and Kia. For the study has been chosen Hyundai vehicle, model i10, year 2014, segment type A, considered an urban vehicle, low fuel consumption and high demand in the local market, in addition to being an imported model.

2.2 Brake disc

Table 1 describes the characteristics of the three brake disc samples identified as spare parts in the national environment.

Table 1- Characteristics of the samples 

2.3 Spectrometry test

The spectrometry test was performed under the standards of ASTM E415-08, is called standard test method for analysis of atomic emission vacuum spectrometry of carbon and low alloy steel. The test consists of inducing a current to an electrode and produce a spark in the disc, the same that would leave a spectrum of light, through the spectrum can be determined the composition of the material. The procedure was carried out in a standardized national laboratory. With spectrometric results, the carbon equivalent (CE) of each sample is calculated, using equation 1, for quantitative comparison of the samples.

𝐶𝐸 = %𝐶 + 0.31%𝑆𝑖 + 0.33%𝑃 − 0.027%𝑀𝑛 + 0.40%𝑆 (1)

The carbon results of brake disc are compared with SAE J431 standard. In table 2, describes compositions for automotive gray iron according SAE J431 standard.

Table 2- Typical base compositions for automotive gray cast iron 

2.4 Metallographic test

The metallographic test was performed under the ASTM A247-16A standard, which is called the standard test method for evaluating the microstructure of graphite in iron foundries. The matrix was analyzed under the microscope, with a resolution of 500X, and a resolution of 100X was used for the morphology and size of the flakes. The test piece result is then compared with the standardized standards in ASTM A247. Both major and minor elements have a direct influence on the morphology of flake graphite. The typical graphite shapes for flake graphite are shown in Figure 1.

Figure 1: Types of graphical distributions, according to ASTM A247 

In figure 1, Type A graphite is found in inoculated irons cooled with moderate rates. In general, it is associated with the best mechanical properties, and cast irons with this type of graphite exhibit moderate undercooling during solidification. Type B graphite is found in irons of near-eutectic composition, solidifying on a limited number of nuclei. Large eutectic cell size and low undercoolings are common in cast irons exhibiting this type of graphite. Type C graphite occurs in hypereutectic irons as a result of solidification with minimum undercooling. Type D graphite is found in hypoeutectic or eutectic irons solidified at rather high cooling rates, while type E graphite is characteristic for strongly hypoeutectic irons. Types D and E are both associated with high undercoolings during solidification.

2.4.1. Metallographic Specimens

For the metallographic test, standardized specimens produced in the wear and failure laboratory are used, designated with numbers 1, 2 and 3, according to ASTM E-3 standards for each brake disc, for convenience, specimens to be polished for metallographic examination are generally not more than about 12 to 25 mm square, as shown in figure 2. Specimens embedded in plastic to protect them from damage and to provide a uniform format for automatic preparation.

Figure 2: Brake disc test specimens and specimen removal area 

For each test it was necessary to machine a 2x2 test tube. The test pieces were taken from the braking track, as shown in figure 2. The selection of test specimens for metallographic examination is extremely important because, if their interpretation is to be of value.

3. Results

3.1 Spectrometry of brake disc test pieces

The results of the metal element spectrometry for each specimen are shown in Table 3.

Table 3- Composition of metal elements of brake disc specimens 

Source: Extractive Metallurgy Laboratory EPN.

The test detects 15 components in each sample, with variations in value for each one. For materials with applications for brake discs and drums, a minimum of 3.4 % carbon content and a pearlitic microstructure is required, according to the grades of grey iron proposed by the SAE J431 standard. For each sample analyzed, this requirement is met, however, sample A presents 23 % and 24% more carbon than samples B and C, respectively.

With regard to the influence of the composition on the microstructure of the material, the carbon equivalent (CE) plays a large role in the distribution and size of the graphite flakes, as well as in the matrix, which gives certain characteristics to the brake disc material. The results for carbon equivalent are shown in Figure 3.

Figure 3: Carbon equivalent (CE) comparison of specimens 

In terms of the composition of the material, between samples B and C, they offer no major difference, however, there is a clear difference with sample A. The carbon equivalent of sample A is 18 % and 20% higher than that of samples B and C, which has a significant influence on the microstructure, since a higher carbon content leads to greater growth of the graphite flakes.

Five elements are involved in the calculation of the EC: carbon (C), silicon (Si), manganese (Mn), phosphorus (P) and sulphur (S). According to the SAE J431 standard, minimum compositions are established for five elements, specimen’s compositions are compared in the figure 4.

Figure 4: Comparison of carbon, silicon and manganese of brake disc test pieces 

Carbon and silicon are the most influential elements in the formation of graphite, silicon acts as a graphitizer, inhibiting carbon so that it does not combine with another element to form graphite flakes, while manganese acts as a stabilizer of carbides(Askeland,2017).

The specimen of sample A, having a higher carbon and 17 % less silicon in relation to samples B and C, allows the brake disc A, to generate a higher growth of graphite flakes.

Both sulphur and phosphorus are found in proportions of less than 1 %, as shown in figure 5, because both in high proportions give fragility to the material, the sulphur has a function opposite to silicon acts as an antigraffiti and in high quantities over 1 % can cause cavitation.

Figure 5: Phosphorus(P) and Sulphur(S) comparison of the specimens 

In the case of Sulphur, as it is an anti-graffiticide, the sample A specimen has 23 % less in comparison to specimen’s B and C, giving the brake disc greater graffiti.

3.2 Metallography

Table 4 shows the results of the metallographic test specimens. Each specimen has a pearlitic matrix, however, there is a different distribution and size of the flakes, which contribute with characteristics such as hardness and internal lubrication.

Table 4- Metallographic tests for specimens 

Source: Extractive Metallurgy Laboratory EPN

Comparing the different brake discs, it is found that sample A has a higher carbon content, which encourages more growth of the graphite flakes. The chemical composition of the material is involved in the growth of graphite flakes, the lower the EC, the smaller the grain size.

3.3 Discussion

According to, Gutierrez, N. & Vinueza Lozada, A. (2018), the existence of zinc reduces the heat flow between brake pad and disc, in sample A, a higher percentage of zinc is observed in relation to samples B and C, therefore, these samples would increase the working temperature during the braking action.

According to Kharate, N. & Chaudhari, S (2018), their study indicates a higher natural frequency oscillation in steel disc with respect to cast iron under similar operating conditions, therefore the existence of higher carbon equivalent, indicates a trend of oscillation in lower operation, such would be the case of the disc in sample A.

According to the studies by Canibano, E., Gonzalez, M. & del Amo, O. (2005) and Cherrez-Troya, M., Martínez-Gómez, J., Peralta-Zurita, D. & Llanes-Cedeño (2018), there are several factors to establish the appropriate conditions of a brake disc, but they are independent of the disc geometry, the blade geometry, the type of test, due to the robustness of the design methodology and the properties of the manufacturing material.

5. Conclusions and recommendations

The auto parts denoted as samples A, B and C, can be offered as brake disc replacement parts, sample A being the one with the best mechanical properties for the assigned function.

It was determined that the three samples of brake disc material, meet the specifications of SAE J431, which indicates the proposed carbon requirement for the manufacture of automotive brake discs and drums, must contain at least a 4.3 % carbon equivalent with pearlitic matrix.

Graphite flakes provide hardness and internal lubrication to the material, these two factors in a brake disc can increase the resistance to frictional wear, allowing a longer life in sample A.

Referencias

Askeland, D. R. y Wright, W. J. (2017). Ciencia e ingeniería de materiales. México: Cengage. [ Links ]

Belhocine, A. y Bouchetara, M. (2012). Thermal Behavior of Full and Ventilated Disc Brakes of Vehicles. Journal of Mechanical Science and Technology 26(11): 3643–3652. https://doi.org/10.1007/s12206-012-0840-6 [ Links ]

Bosch. (2015). Manual de la técnica del automóvil. Alemania. [ Links ]

Cañibano, E.; González, M. y del Amo, O. (2005). Diseño de discos de freno desde un punto de vista multidisciplinar. DYNA, 80(3), 27-32. [ Links ]

Chérrez-Troya, M.; Martínez-Gómez, J.; Peralta-Zurita, D.y Antonio Llanes-Cedeño, E. (2018). Métodos multicriterio aplicados en la selección de un material para discos de freno. Ingenius. Revista de Ciencia y Tecnología, (20), 83-95. [ Links ]

Hwang, P. & Wu, X. (2010). Investigation of Temperature and Thermal Stress in Ventilated Disc Brake Based on 3d Thermo-Mechanical Coupling Model. Journal of Mechanical Science and Technology, Vol. 24, No. 1, 81–84. doi: 10.1007/s12206-009-1116-7. [ Links ]

Rodríguez García, N. J. y Nieto Sánchez, I. C. (2017). Consideraciones para el diseño de un sistema diagnóstico de frenos de disco en un vehículo particular. Avances: Investigación en Ingeniería, 14(1), 76-94. [ Links ]

Gutierrez, N., & Vinueza Lozada, A. (2018). Analysis by the finite element method of the behavior of the ABS brake pads with materials based on steel and zinc discretizing the continuous element using CAE software. Enfoque UTE, 9(1), pp. 188 - 203. https://doi.org/https://doi.org/10.29019/enfoqueute.v9n1.259 [ Links ]

Kharate, N. & Chaudhari, S (2018). Effect of material properties on disc brake squeal and performance using FEM and EMA approach. Materials Today: Proceedings, vol. 5, no. 2, 4986–4994. doi: https://doi.org/10.1016/j.matpr.2017.12.076. [ Links ]

Lascano Piedra, D. A. (2017). Análisis de los discos de freno de un Chevrolet Aveo cuando está sometido a diversas temperaturas para determinar el cambio de propiedades del mismo (Bachelor's thesis). Ingeniería Automotriz [ Links ]

Maleque, M. Dyuti, S. & Rahman, M. M. (2010). Material selection method in design of automotive brake disc. Proceedings of the World Congress on Engineering 2010 Vol III, 06. [ Links ]

Paredes Salinas, J., Pérez Salinas, C., & Castro Miniguano, C. (2017). Analysis of the mechanical properties of the composite of polyester matrix reinforced with glass fiber 375 and cabuya applied to the automotive industry. Enfoque UTE, 8(3), pp. 1 - 15. https://doi.org/https://doi.org/10.29019/enfoqueute.v8n3.163. [ Links ]

Piña, M. (2008). Estudio de la influencia de la morfología grafítica sobre las propiedades mecánicas de los discos de freno automotrices de hierro gris hipereutecticos. Mexico D.F.: Instituto Politecnico Nacional. [ Links ]

Rodrigues, J. (2004). Diseño y fabricación de hierros grises hipereutécticos de baja aleación para discos de freno. México D.F.: instituto Politécnico Nacional. [ Links ]

SAE Internacional (2018). SAE J431: Automotive Gray Iron Castings.USA. [ Links ]

SENAE. Servicio Nacional de Aduana del Ecuador. [Online]. Available: https://goo.gl/X4Jk9k [ Links ]

Tuckart, W., Molinari, E., Caso, l., & Prieto, G. (2014). Estudio de falla prematura de disco de freno. Universidad Santiago de Chile. [ Links ]

Received: March 09, 2020; Accepted: June 04, 2020

Creative Commons License Esta obra está bajo una Licencia Creative Commons Atribución 3.0 Ecuador.